Keywords : Aluminium plate | Aluminum foil strip
Send Inquiry x
I can help you
Send
PRODUCTS
PRODUCT CENTER
SERVICE PHONE
86 17344894490
banner
Location : Home/Aluminum Plate/ 5005 5086 5052 5083 Aluminum Tread Checkered Plate Sheets

5005 5086 5052 5083 Aluminum Tread Checkered Plate Sheets

Last Updated :2023/07/03

5005 5086 5052 5083 Aluminum Tread Checkered Plate Sheets
 
Aluminium alloy 5005 5086 5052 5083 contains nominally 0.8% magnesium. It has medium strength, good weldability, and good corrosion resistance in marine atmospheres. It also has the low density and excellent thermal conductivity common to all aluminium alloys. It is the most commonly used grade of aluminium in sheet and plate form.
Corrosion Resistance 5005 5086 5052 5083 has the same high resistance to general corrosion as other non heat treatable aluminium alloys. It also has the higher resistance to slightly alkaline conditions common to the 5000 series alloys. The atmospheric corrosion resistance of 5005 is similar to that of 3003.

 
When anodised to improve corrosion resistance, the film on 5005 5086 5052 5083 is clearer than on 3003, and gives better colour match with 6063 architectural extrusions.
5005 5086 5052 5083 Aluminum tread checkered plate sheet make it an ideal material which is suitable for both indoor and outdoor use thanks to its excellent characteristics. Other names for used aluminium checker plate are diamond plate, tread plate or Durbar floor plate, checkered plate.
 
Indestructible and resilient despite low weight
 
5005 5086 5052 5083 Aluminum tread checkered plates sheets are very resilient against aggressive substances and therefore, they regarded as indestructible. Due to their durability, they are used in many different areas because they do not lose their shape or look, even after a long time. Whether industrial floors, airplanes, ships and vehicles, or stairs indoors or outdoors -5005 5086 5052 5083 aluminium checker plates are a popular material which is appreciated for its excellent properties, the high resilience and the low weight. Even designers use these plates due to their decorative look.

 
Attractive pattern ensures slip resistance
 
During production, the pattern is applied to the plate by forming rolls which are pressed onto the plate with a large force. In doing so, the bottom of the plate remains plain. It is not possible to emboss the aluminium plate subsequently.
Due to the diagonally finned structure, the plate becomes slip-resistant which is why it is also suitable for use outdoors and in wet areas. In addition to the finned structure, there are many other shapes and patterns which provide the same characteristics.
 
Depending on the type of plate, 1 to 5 bars are arranged next to each other, forming a checked pattern. It is differentiated between 1 bar(diamond), 2 bar, 3-bar and 5-bar patterns.

Alloy Si Fe Cu Mn Mg Cr Ni Zn Ti Ga V Each Total Alu
5005 0.3 0.7 0.2 0.2 0.5--1.1 0.1 - 0.25 - - - 0.05 0.15 Remainder

Alloy Si Fe Cu Mn Mg Cr Ni Zn Ti Ga V Each Total Alu
5086 0.4 0.5 0.10 0.20-0.7 3.5--4.5 0.05-0.25 - 0.25 0.15 - - 0.05 0.15 Remainder

Alloy Si Fe Cu Mn Mg Cr Ni Zn Ti Ga V Each Total Alu
5052 0.25 0.4 0.1 0.1 2.2--2.8 0.15-0.35 - 0.10 - - - 0.05 0.15 Remainder

Alloy Si Fe Cu Mn Mg Cr Ni Zn Ti Ga V Each Total Alu
5083 0.4 0.4 0.10 0.40-1.0 4.0--1.0 0.05-0.25 - 0.25 0.15 - - 0.05 0.15 Remainder
 

Alloy 5005 5086 5052 5083
Temper H114, H224, H12, H14, H16, H18, H32, H34, H36, H38, T4, T6, F
Surface Bright finish, Mill finish
Bar Difference 1 bar (Diamond), 2 bar, 3 bar, 5 bar

Available Dimension
  Mill finish Surface Bright finish Surface
Thickness  (mm) 1.00---6.50mm 1.20---6.50mm
Pattern height Sheet Thickness from 1.0mm to 2.0mm,  bar height: 0.50mm Sheet Thickness from 1.0mm to 2.0mm,  bar height: 0.50mm
Sheet Thickness from 1.0mm to 2.0mm,  bar height: 1.00mm Sheet Thickness from 1.0mm to 2.0mm,  bar height: 1.00mm
Sheet Thickness above 2.0mm,  bar height: 1.50mm Sheet Thickness above 2.0mm,  bar height: 1.50mm
Width (mm) Maximum 1500mm Maximum 1650mm
Length (mm) Maximum 6000mm Maximum 6000mm
Paper interleaves On request for selected On request for selected
Normal size 1200×2400mm, 1219×2438mm,  1219×3048mm 1200×2400mm, 1219×2438mm,  1219×3048mm
 

Application
 
A. 5005 5086 5052 5083 Aluminum tread checkered plate sheet has good skid resistance. So it is usually used in the loading ramps, trench covers, dock flooring, stair treads and even for the car, truck, ambulance and fire truck.
B. It has the decorative function, so it can be used as decoration wall panels, cabinet and ceilings.
C. Because of the anti- corrosion, it can be used in the chemical industry, or in the decoration of the ship and port facilities.



Compliance with international standards
 
EN 573-3 Aluminium and aluminium alloys - Chemical composition and form of wrought products – Part 3: Chemical composition and form of products
EN 1386 Aluminium and aluminium alloys - Tread plate - Specifications
EN 15088 Aluminium and aluminium alloys - Structural products for construction work - Technical conditions for inspection and delivery